Hynix launches 321-layer NAND
78 points by WaitWaitWha 12 hours ago | 32 comments
  • kridsdale3 11 hours ago |
    When I was in school studying NAND devices (2004-2010) we were quite apprehensive at the long term quantum stability of 4-layer devices.

    This (the past 20 years of improvement) is an incredible feat of engineering.

    • duskwuff 11 hours ago |
      This is 321 physical layers of silicon in an IC, not 321 charge levels.

      QLC flash - with 16 charge levels, for four bits per cell - is pretty common nowadays, but that's as far as it goes so far. And stability is indeed a concern; modern flash devices rely heavily on error correction.

      • cma 4 hours ago |
        Memory like HBM uses stacking of silicon layers, but NAND flash isn't layers of silicon, it's other materials for capturing and holding charge with still just one silicon plane it's all built on top of I believe.
  • hinkley 11 hours ago |
    Where’s the point where you figure out how to stack chiplets perpendicular to a backplane instead of doing lithography 300 times on the same chip?
    • duskwuff 11 hours ago |
      That's kind of what we're doing already, although the stacking is parallel, not perpendicular. A lot of the innovation is in how the dies are tied together, cf. https://www.anandtech.com/show/9520/toshiba-brings-throughsi...
    • creer 10 hours ago |
      This is an interesting testament to manufacturing reliability - that they can go to so many layers and still achieve good yield.
    • mlyle 8 hours ago |
      As others here have pointed out -- you don't need to do lithography 300 times. The big breakthrough of 3D NAND is depositing alternating layers of films to build most of the layers.

      This is 3 stacks of >100 layers.

  • fodkodrasz 11 hours ago |
    > triple level cell-based 4D memory

    What does 4D memory mean?

    • matja 10 hours ago |
      Nothing - just marketing. It's their 2nd gen Periphery Under Cell (PUC) device.
    • wrs 10 hours ago |
      It’s marketing speak. 3D flash (stacked chips) with the control circuits stacked underneath instead of to the side. So it’s one louder.

      https://www.tomshardware.com/news/sk_hynix-debuts-4d_nand,37...

    • K0HAX 10 hours ago |
      Bigger number = more betterer
    • tbrownaw 7 hours ago |
      It'd have to be something involving time... maybe have each cell be a delay line? Or a resonant cavity, and store multiple bits at different modes? Not sure how either could be made small enough to be worth it though...
  • Animats 11 hours ago |
    Wow. What's the yield like? Are some bits bad and bypassed during testing?
    • timschmidt 11 hours ago |
      > Are some bits bad and bypassed during testing?

      Always. All digital storage media depends on error correcting codes and sector-remapping these days.

  • Neywiny 11 hours ago |
    I just want smaller SPI flash for embedded :( it's been over 10 years since there's been improvement in that space
    • duskwuff 10 hours ago |
      WLCSP-8 is pretty damn small already, at ~1.5mm square. Hard to get much smaller.
      • Neywiny 10 hours ago |
        But they aren't high capacity. As far as I've seen, we've been stuck on the same XY size 512 Mb dies for over a decade. Even now, Infineon is claiming they have a series that'll go up to 4 Gb but is still at the standard 2 Gb maximum. NOR hasn't gotten any denser in forever.
        • duskwuff 9 hours ago |
          What's the use case for a NOR flash that large? Even at 2 Gbit, you're probably better off with something optimized for density like eMMC.
          • Neywiny 8 hours ago |
            The use is that there's often (in my field) no space for an 11.5x13 eMMC. There are some that are slightly smaller, but as you brought up the wlcsp-8, there's nothing like eMMC/high capacity NAND density scaled down. If I had the bits/mm^2 of even NAND 5 years ago, I'd be a happy camper. But that's life.
            • mlyle 8 hours ago |
              There's QSPI NAND parts available; they're just annoying to use.

              https://www.digikey.com/en/products/detail/winbond-electroni...

              https://www.digikey.com/en/products/detail/alliance-memory-i...

              There's also 9x8mm eMMC. The big issue with shrinking it further is that it tends to be a module with a separate controller doing lots of things to make the memory reasonable to use.

              • Neywiny 6 hours ago |
                Yeah those are what I'm looking at, but even then we've been at 8Gb for years. Manufacturers only want SLC NAND in these for valid reasons and I guess the market isn't pushing for now. The 9x8 is useful but the 3.3v that eMMC wants means I can't power off a single cell li-ion without a boost. It's all a nightmare. Trust me I've looked for solutions, unless you know of any silver bullets that came out recently.

                And as you surely know, I usually can't boot from NAND (due to the aforementioned annoyance) so I'd have a boot flash and a storage flash and that's unideal.

                I'll note though that the controllers are small. You can RE the die size of a common eMMC<->NAND controller and it's much smaller than 9x8. I won't share which because I honestly don't remember if we got an NDA in place but considering they all stack dies in there anyway, I don't really see that as the size driver.

        • shadowpho 8 hours ago |
          There’s no money in it. Embedded doesn’t pay compared to phones/tablets. So companies are putting their money into that
          • Neywiny 8 hours ago |
            I'm fully aware of why there's been no improvement, it just sucks for me.
            • xyzzy_plugh 4 hours ago |
              I left embedded when I realized everything, at least in my neck of the woods, was going to end up being cramming phone parts into things that were not phones. The writing has been on the wall for a while now.

              Even now as a consumer I can see the stagnation. It's the same parts year after year. Or you become a phone. You have my sympathy.

  • tomcam 10 hours ago |
    Cookie permission dialog is the worst I have encountered in months
    • randomjoe2 10 hours ago |
      Thank god for ublock origin filters, i have all the optional filter lists, I never see those things. EVER.
    • CoastalCoder 4 hours ago |
      I noticed that as well.

      I'm not sure what the rules are, but I had to disable a surprising number of "legitimate interests" related to advertising.

  • StringyBob 9 hours ago |
    What does 'layer' mean in this context? I'm only familiar with planar style logic process nodes which have maybe up to 20 layers (and way more lithography steps to manufacture those layers), but I am completely ignorant of how the term is used for a flash process node.

    How many layers are needed for each physical cell? Is it 1,2, or a lot more? Is this effectively 321 physical TLC cells stacked vertically and some planar style logic at the bottom of the stack.

    Also, where do multiple pieces of silicon factor into this - I assume we might be up to 16 silicon dies deep with through-silicon-vias, which would mean a cross section of a package could actually have 5000 layers - that sounds crazy!

    • brennanpeterson 9 hours ago |
      Probably done with 3 separate litho/etch layers, where they etch and process in groups of 110 or so.

      Each of those layers can have a cell, so if you have a tlc device at a 100nm pitch, you have a density of 321*3/(1e-4)^2 bits/mm, or about 1e11bits/mm2.

      Fun reference: atomic density is 1atom/.5nm, so 1/5e-7^2, or 4e12/mm2 ish.

      Not too far away.

      • StringyBob 8 hours ago |
        Amazing, I had no idea how far things had diverged between logic and flash since the move to 3D.

        https://borecraft.com/files/Comparison_Current_NAND.pdf (from 2019) has some of the cross-sections I was looking for - and that only goes up to 96 layers!

  • RicoElectrico 9 hours ago |
    What's interesting is that these devices don't need 321+ litho steps; the vertical layers are all defined with deposition. Lithography step count isn't layer dependent it seems.

    https://youtu.be/ANHzVOiUwGI

    https://thememoryguy.com/3d-nands-impact-on-the-equipment-ma...

  • drpixie 29 minutes ago |
    Title should probably be "Hynix launches 321-layer NAND RAM".